Resetting Macard N300 to Factory Settings in Minutes

Macard WiFi extender is one of the best WiFi boosters which extend every network signal in your house.

One of the models is Macard N300 extender. Here, we will share the whole Macard WiFi extender setup to boost up your router signals.

Why You Should Reset the Macard N300 Extender?

Forgot the admin password. You set it once, wrote it on a sticky note, and now it’s gone. Reset = back to defaults.
WiFi keeps dropping. Sometimes the extender just gets stuck in some loop. Reset clears it.
You moved to a new router. The extender doesn’t know the new SSID/password until you reset and reconfigure.
It’s acting plain buggy. Lag, disconnects, random blinking lights—it’s usually faster to reset than troubleshoot each little thing.

How to Reset Macard N300 Extender?

Find the reset button.
It’s tiny. Like, you need a paperclip or something sharp. Look on the side or bottom of the extender. It’s recessed, so don’t waste time poking random LEDs.

Power it on first.
Reset only works when the extender is powered up. Plug it into an outlet, wait until the lights stop freaking out.

Hold reset for ~10 seconds.
Stick the paperclip in and press. Keep holding until you see the lights flash off/on (mine blinked, then all went dark, then came back). That’s your sign it’s actually resetting.

Let it reboot.
Give it a minute. It’ll come back like it was brand new out of the box. Default network name shows up again (something like MACARD-EXT).

Reconfigure from scratch.
Connect to that default network, then go through the setup wizard again in your browser. Usually at 192.168.10.1 (if that doesn’t work, check the little manual or bottom label).

How to Reconfigure N300 Extender?

Plug it in halfway between your router and the dead zone. Not too close to the router, not too far. Middle ground. You want it where it still catches solid WiFi but can also reach the weak spot.
Connect to its setup WiFi. On your phone or laptop, check your WiFi list. You’ll see something like NETGEAR_EXT (if it’s a Netgear N300) or whatever brand you’ve got. Connect to that. No password at this point.
Open the setup page. Open up a browser and go to 192.168.1.250 (or sometimes it’s mywifiext.net). If it doesn’t load, try both. Worst case, check the manual stuck on the bottom of the extender.
Run the wizard. It’ll ask you for your main WiFi name and password. Punch those in. That’s the “extend” part. After that, it’ll create a new WiFi network (usually with _EXT tagged onto the end).
Reconnect everything. After the extender reboots, you’ll see that new network pop up. Join it with the same WiFi password you use on your main router. From there, all your devices should be able to connect.

So this is how you can re-complete the Macard N300 setup, now learn a few tips from the experts.

Other Troubleshooting Tips than Reset

Restart the Macard extender.

Obvious, but not the same as reset. Full power off, wait a minute, then boot it up. You’d be shocked how many glitches die right there.

Check cables and ports.

Loose HDMI, dusty charging port, bent USB pins. Half the time it’s not the software—it’s a physical connection failing. Wiggle things around, swap cables if you’ve got extras.

Kill background junk.

Apps, processes, random tabs eating RAM. Close them. If it’s a phone, check battery usage to see what’s hogging resources.

Update drivers/firmware.

outdated drivers cause weird bugs. Grab the latest from the official site, not some sketchy download mirror.

Safe mode / diagnostic boot.

Run it stripped-down and see if the issue still happens. If it doesn’t, you know it’s some third-party app or add-on messing you up.

Log out / re-login.

Sounds silly, but cached credentials or corrupted profiles can make services act drunk. Logging back in resets the session without nuking the whole system.